TECHNICAL DATAModel:BMSL1233Dimensions (L × W × H): 13 × 18 × 23 cm
Weight:approx. 420 gBattery type:4× 1.5 V; C-LR14
SPOTLIGHTProtection class:IIIIlluminant:2× LED, non-removable (1 LED/spotlight head)Output:2× 5 WSupply voltage:3.7 V Service life:20,000 hMax. projection area:2× 2,829 mm2Luminous flux:2× 250 lmColour temperature:6,300 KColour rendering index (Ra): > 70
Warming up time (95 %): < 1 s
Number of switching cycles: > 15,000
Dimmable:NoRisk group(according to EN 62471:2008):1Minimum distance to illuminated objects:1 mPlastic protective screen: ∅ 60 mm, thickness 3 mm
Type of protection: IP44
MOTION SENSORSensor angle:approx. 140°Rotation:90°Sensor range:7 m ± 1 mSensitivity:2 to 20,000 lux (adjustable)Lighting duration:approx. 5 s to 7 min.(configurable)
SAFETY WARNINGS
1.Keep children away from the spotlight.
2.Before start-up, remove all protective films.
3.Keep the spotlight away from water, other liquids, open flames and hot surfaces.
4.Do not hang any objects over the spotlight and do not cover it.
5.Maintain a distance of 1 m between the spotlight and easily flammable materials.
6.Do not continue to use the spotlight if it exhibits damage.
7.Only replace damaged parts with corresponding original spare parts.
8.Do not open the housing and do not make any modifications to the spotlight.
9.Have only qualified professionals perform repairs.
10.Make sure that the polarity is correct when inserting the batteries.
11.Only use batteries of the same type.
12.Do not mix used and new batteries together. Always change all of the batteries at the same time.
13.Remove empty batteries from the spotlight.
USER INSTRUCTIONS
![Dynaplus Dual-Head Led Outdoor Sensor Light来自中国供应商](/public/media/LazyImage_placeholder.09bec84d.svg)
![Dynaplus Dual-Head Led Outdoor Sensor Light来自中国供应商](/public/media/LazyImage_placeholder.09bec84d.svg)
![Dynaplus Dual-Head Led Outdoor Sensor Light来自中国供应商](/public/media/LazyImage_placeholder.09bec84d.svg)
MOUNTING THE SPOTLIGHT
1. Choose a suitable surface for installation (see chapter section “Choosing an installation location”).
2. If necessary, remove the rear panel 5 from the spotlight by unscrewing both fixing screws 2.
3. Hold the rear panel on the installation surface and mark both locations for fastening. Use a spirit level if necessary.
4. Choose mounting materials which are suitable for the installation surface. The supplied screws 12 and dowels 13 are suitable for concrete and brickwork.
5. Screw the rear panel into the locations for fastening according to the properties of the installation surface. Do not apply excessive force in the process.
6. Place the housing of the spotlight onto the rear panel.
7. Fasten the housing on the rear panel by screwing the fixing screw tight.
OPERATION
Choosing a sensor area
You can configure the sensor area by turning the motion sensor housing. The motion sensor housing can be turned by 90°. The sensor angle of approx. 140° does not change in the process. Choose the required sensor area by turning the motion sensor housing 3 .
Choosing a lighting duration
If necessary, turn the motion sensor housing 3 to reach the controller for the lighting duration 7.
Choose the desired lighting duration between approx. 5 seconds and approx. 7 minutes by turning the controller in the corresponding direction. Turning the controller clockwise increases the lighting duration. Turning the controller anticlockwise decreases the lighting duration.
Choosing the sensitivity
You can specify at what brightness (e.g. from dusk) the motion sensor reacts and switches on the spotlight: Choose between approx. 2 lux (dark) and 20,000 lux (bright). If necessary, turn the motion sensor housing 3 to access the sensitivity controller 4. Choose the desired sensitivity by turning the controller in the corresponding direction: Turning the controller clockwise increases the sensitivity so that the motion sensor 8 will react even in a bright environment (e.g. in daylight). Turning the controller anticlockwise decreases the sensitivity so that the motion sensor will only react in a darker environment (e.g. at night-time).
Adjusting the spotlight heads
You can turn both spotlight heads approx. 180°. The maximum angle of aperture between the two spotlight heads is approx. 320°. You can also move each of the spotlight heads approx.
90° downwards and approx. 90° upwards. Adjust the spotlight heads 1 according to your requirements.
Switching the spotlight on and off
Using the power switch you can either turn the spotlight on or off or operate it in automatic mode.
In automatic mode, the spotlight will switch on if the motion sensor is activated. To switch the spotlight on, set the power switch 6 to the ON position. To switch the spotlight off, set the power switch to the OFF position. To activate automatic mode, set the power switch to the AUTO position.
![Dynaplus Dual-Head Led Outdoor Sensor Light来自中国供应商](/public/media/LazyImage_placeholder.09bec84d.svg)